Horizontal Ф80 Rod Copper Continuous Casting Machine 200Kw Holding
1. technical parameters
1.1 main technical parameters
1.1.1 casting type: two strands
1.1.2 casting specification: Ф10~80
1.1.3 raw material: red copper
1.1.4 casting speed:
pulling speed: 0~43mm/s (stepless to adjust)
pushing speed: 0~43mm/s (stepless to adjust)
Melting furnace: 550KW
Holding furnace: 200kw
1.1.6 production capacity: 500tons per month(calculate as the
1.1.7 noise: ≤80db
1.2 installation level
- The equipment has complete functions, performance parameters
reasonable, the whole line can be controlled automatically .
- The system adopt AC servo control system from japan, SIEMENS PLC
from germany, maintained conveniently, reliable performance, the
technics can be widely used.
- The control system, electric elements, buttons, indicator light are
all original binding products from well-known factories.
- Adopt PLC programmable control.
- The technological process parameters can be preset.
1.3 technical instruction
This continuous casting line includes melting furnace, holding
furnace, crystallizer, tractor, saw, electric control system,
hydraulic control system and cooling system.
The 550kw power frequency induction melting furnace and The holding
furnace of 200KW power frequency induction furnace with the same
body,there is a refined furnace chamber between the melting furnace
chamber and holding furnace chamber,it is composed by upper furnace
body, inductor, bracket, hydraulic system. The furnace shell of
upper furnace body is welded with Q235A steel plate. The bottom
have flange connected with inductor assembly. There are
hydrocylinder and bearing pedestal at the two sides can tilt
furnace 45°. The indutor assembly is composed with shellbody,
copper channel, iron core, loop, water jacket and refractory
material. the loop is made of flat copper tube coated with
double-fibreglass; the water jacket is made of stainless steel
plate of 1Cr18Ni9Ti.
184.108.40.206 main parameters of melting furnace
efficient capacity: 2.5t
Total capacity: 3t
Rated power: 550KW
Rated voltage: 380V
Consumption of cooling water: 5m³/h(move in cycle)
220.127.116.11 holding furnace
efficient capacity: 2t
Total capacity: 3t
Rated power: 200KW
Rated voltage: 380V
Consumption of cooling water: 3m³/h(move in cycle)
The crystallizer is composed by framework, sealed filling frame,
inner sleeve, outer sleeve, graphite die, seal components.
Water cycle type is one entry one exit.
Water pressure: 0.6~0.8Mpa
18.104.22.168 The tractor is composed by pedestal, electric machine,
speed reducer, gapless gears, traction roller, screw down device.
The pedestal is frame structure welded with Q235A steel plate, the
electric machine choose AC servo motor from japan.
22.214.171.124 main parameters
Power of motor: 7.5KW
Rated rorate speed: 1500r/min
Using rotate speed: 200~1200r/min
Pulling and pushing speed: 0～43mm/s
Shortest stop time: 0.01s
126.96.36.199 The saw is composed by hydraulic system, saw noumenon,
guide rail. The saw can move along the guide rail. After finsh the
cutting, the saw will be pushed back by a oil cylinder.
188.8.131.52 main parameters
Max sawing diameter: 100mm
Cutting length :as the client requirement
1.3.6 Water cooling system
184.108.40.206 Main catalogs
(1) cooling water flow: 40m³/h
(2) water pressure of the system: max0.6Mpa
(3) water inlet temperature: MAX 30℃
(4) water outlet temperature: MAX 45℃
(5) hardness 150~180ppm
1.3.7 Electric control part of horizontal continuous casting line
Electric control part divide into power frequency electric furnace
AC control part and auomatic control part:
- Power frequency electric furnace AC control part
(1) Melting furnace adopt three-phases. Output working pressure is
90~380V, eight gears to regulating voltage, noload stepness
automatic coupling voltage regulator(three phases balance).
(2) Holding furnace use electromagnetic induction voltage
regulator, can make load and stepless voltage regulating, it’s easy
to control furnace temperature.
(3) the bottons and indictors are from shanghai, all the relay,
switches are from famous factory.
b. Automatic control part
(1) Summation of the system
This part include main control PLC, human-machine interface,
transducer, actuator, drive element and appurtenances
The horizontal continuous casting line use a SIEMENS PLC as the
main controller, all of the transducer datas are access this PLC
and all the actuators are controlled by the PLC. The datas after
treatment by the PLC will be transferred to actuator and the
actuator control the set’s running.
Through exchange datas between human-machine interface and PLC, all
of the running state and running parameters can be adjusted.
This system has the following characteristic: use mature SIEMENS
products and advanced control system, software developed by
ourselves to make the equipment operated easily, the system stable
and reliable, compatibility good; PLC main controller and
human-machine interface separation layout, it can reduce artificial
operation and disturbance for control center from the third part;
cost moderate, mainantenance parts and extended parts complete and
in plenty supply.
All the transducers and actuators are use high quality elements,
the principle is stable, reliable, high precision, installation and
mainantenance convenient and price moderate, drive element adopt AC
All of the electric control equipments are installed in a series of
vertical type cabinets, possessing protection equipment and
(2) Main controller
Main controller PLC adopt SIEMENS ,it can coordination with many
machine and support external connect veries function extending
(3) Holding furnace
Holding furnace include temperature test and temperature control,
the test use a high temperature thermocouple accessed to
temperature test module of main controller. Heating voltage and
current are both through electric quantity transducer transferred
to main controller PLC.
(4) Traction part
Use a set of AC servo electric machine from japan an’chuan,
brushless servo amplifier and servo power supply to control running
of the hollow bar, including the speed and time of pulling, stop
and backward pushing.
Main controller PLC use serial data interface to control the
(5) Human-machine interface
This interface use touch screen display of Eview, the display can
modify and display running parametres, it has veries alarming
signals. Running parameters contain pulling travel, pushing 1
travel, pushing 2 travel, pulling speed, pushing 1speed, pushing 2
speed, pulling stop time, pushing 1stop time, pushing 2 stop time,
speed curve and smoothing running linear velocity, etc. alarming
signal contain holding furnace temperature overrun, low pressure
water supply water pressure low, low pressure water output water
temperature high, crystallizer water supply water pressure low,
over position and over load of equipments alarming. The interface
also has the function of copper liquid in holding furnace
1.3.8 Hydraulic system
Hydraulic system include hydraulic system of melting furnace and
holding furnace, the plunger pump is from shaoyang.
Hydraulic system of furnace
oil supply pressure: 12Mpa
rated flow: 40L/min
cleaness of system: NAS9grade
working temperature: 20～55℃
2. sell’s scope of supply
1. melting and holding furnace one(united furnace)
2. crystallizer two
3. tractor one
4. saw one
5. water supply system one
6. mould for holding furnace one
2.2 hydraulic system one
2.3 electric control system one